Latest [May 25, 2022] NACE-CIP2-001 Exam with Accurate Coating Inspector Level 2 PDF Questions [Q20-Q41] : IT Certification Exam Braindumps : http://blog.braindumpsit.com

Q20. You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:

Correct the errors yourself and suggest the Level 1 inspector be replaced

Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent

Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation

Correct the errors yourself and submit the reports without any further action

Q21. You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor’s supervisor. Upon arriving onsite the Contractor’s supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:

Challenge the supervisor’s authority

Defend the previous inspector

Express a willingness to work with the site team and follow the specification

Suggest to the Owner that the supervisor should be removed from site

Q22. Linings are used on the interior of pipelines to

provide protection against soil chemicals.

afford limited temperature insulation.

protect the transported product.

reduce magnetic polarity.

Q23. Cold-applied tape

are identifiable by its distinct colors, usually light blue, green, Or Grey.

is typically green or led and looks like “painted” finish.

have a cross-linked polyethylene backing and a heat-activated adhesive.

is polyethylene film, heat laminated, ‘With an adhesive layer of butyl glue.

Q24. A failure caused by applying a coating too thinly is known as

failure to cure.

chalking.

cracking.

pinholes.

Q25. You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:

Ignore the additional requirement

Enforce the additional requirement

Call your supervisor

Request clarification from the specifier

Q26. The cost of qualified Coating Inspection is normally offset by:

Lower Application Costs

Lower Coating Life Cycle Costs

Lower Safety Enforcement Costs

Lower Supervision Costs

Q27. All of these are advantages of using repair patches EXCEPT

special tools or equipment are required.

excellent abrasion resistance.

inert to common acids, alkalis, and solvents.

barrier to moisture and corrosion.

Q28. An Inspection and Test Plan is required when:

It is always required

When the Coating Applicator requests one

When the Owner specifies one

When the Inspector requests one

Q29. A single component water borne acrylic coating cures by:

Solvent Evaporation

Coalescence

Co-Reaction

Oxidation

Q30. Inspectors perform tests on linings that they may not perform on exterior coatings because

coatings are more durable than linings.

coatings are expected to degrade over time.

linings protect the contents and the container.

linings are more durable than coatings.

Q31. NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:

True

False

Q32. When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:

Method A – X Cut

Method A – Cross Hatch

Method B – X cut

Method B – Cross Hatch

Q33. In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?

Flow stage

Wetting stage

Cure stage

Gel stage

Q34. As a NACE Level 2 Inspector, NACE clearly indicates that you ate qualified to independently produce final documentation for a shop project.

True

False

Q35. In the event of a conflict between the Product Data Sheet and the Specification:

The Product Data Sheet prevails

The Specification prevails

It is up to the Inspector to decide which one to follow

It is up to the Applicator to decide which one to follow

Q36. When NACE/SSPC WJ 1 is referenced; what type of equipment would the Inspector expect to see on the job:

Power Tools

Abrasive Blasting Equipment

Water Jetting Equipment

Scarifiers

Q37. The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of

urethanes.

inorganic zincs.

epoxies.

powder coatings.

Q38. Antifouling coatings are regulated by international treaties.

True

False

Q39. External coatings applied to buried pipelines are generally tested for:

Gloss level

Chalking resistance

Cathodic disbondment

Solvent resistance

Q40. In which type of concrete are laitance commonly encountered?

Concrete block (poured with a form)

Gunite

Glass fiber cement

Poured (wet cast)

Q41. On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?

Liquid epoxies

Heat-shrink sleeves

Concrete

Coal Tar Enamel