This page was exported from IT Certification Exam Braindumps [ http://blog.braindumpsit.com ] Export date:Sun Oct 6 14:21:02 2024 / +0000 GMT ___________________________________________________ Title: 2023 350-401 Premium Files Test pdf - Free Dumps Collection [Q180-Q202] --------------------------------------------------- 2023 350-401 Premium Files Test pdf - Free Dumps Collection Get ready to pass the 350-401 Exam right now using our CCNP Enterprise Exam Package NEW QUESTION 180Drag and drop the characteristics from the left onto the orchestration tools that they describe on the right. NEW QUESTION 181Refer to the exhibit.The administrator troubleshoots an EtherChannel that keeps moving to err-disabled. Which two actions must be taken to resolve the issue? (Choose two.)  Reload the switch to force EtherChannel renegotiation  Ensure that interfaces Gi1/0/2 and Gi1/0/3 connect to the same neighboring switch.  Ensure that the switchport parameters of Port channel1 match the parameters of the port channel on the neighbor switch  Ensure that the corresponding port channel interface on the neighbor switch is named Port-channel1.  Ensure that the neighbor interfaces of Gi1/0/2 and Gi/0/3 are configured as members of the same EtherChannel ExplanationCauses of ErrdisableThis feature was first implemented in order to handle special collision situations in which the switch detected excessive or late collisions on a port. Excessive collisions occur when a frame is dropped because the switch encounters 16 collisions in a row. Late collisions occur after every device on the wire should have recognized that the wire was in use. Possible causes of these types of errors include:* A cable that is out of specification (either too long, the wrong type, or defective)* A bad network interface card (NIC) card (with physical problems or driver problems)* A port duplex misconfigurationA port duplex misconfiguration is a common cause of the errors because of failures to negotiate the speed and duplex properly between two directly connected devices (for example, a NIC that connects to a switch). Only half-duplex connections should ever have collisions in a LAN. Because of the carrier sense multiple access (CSMA) nature of Ethernet, collisions are normal for half duplex, as long as the collisions do not exceed a small percentage of traffic.NEW QUESTION 182Drag and drop the LISP components on the left to their descriptions on the right. Not all options are used. NEW QUESTION 183Drag and drop the LIPS components on the left to the correct description on the right. Map serverEIDETRNEW QUESTION 184What it the purpose of the LISP routing and addressing architecture?  It creates two entries for each network node, one for its identity and another for its location on the network.  It allows LISP to be applied as a network virtualization overlay though encapsulation.  It allows multiple instances of a routing table to co-exist within the same router.  It creates head-end replication used to deliver broadcast and multicast frames to the entire network. NEW QUESTION 185Refer to the exhibit Drag and drop the snippets into the RESTCONF request to form the request that returns this response Not all options are used NEW QUESTION 186What is the difference between CEF and process switching?  CEF processes packets that are too complex for process switching to manage.  CEF is more CPU-intensive than process switching.  CEF uses the FIB and the adjacency table to make forwarding decisions, whereas process switching punts each packet.  Process switching is faster than CEF. NEW QUESTION 187Refer to the exhibit.Only administrators from the subnet 10.10.10.0/24 are permitted to have access to the router. A secure protocol must be used for the remote access and management of the router instead of clear-text protocols.Which configuration achieves this goal?  Option A  Option B  Option C  Option D NEW QUESTION 188Which statement about multicast RPs is true?  RPs are required only when using protocol independent multicast dense mode.  RPs are required for protocol independent multicast sparse mode and dense mode.  By default, the RP is needed periodically to maintain sessions with sources and receivers.  By default, the RP is needed only to start new sessions with sources and receivers. Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.htmlNEW QUESTION 189Refer to the exhibit.R1 has a BGP neighborship with a directly connected router on interface Gi0/0.Which command set is applied between the iterations of show ip bgp 2.2.2.2?  R1(config)#router bgp 65001R1(config-router)#neighbor 192.168.50.2 shutdown  R1(config)#router bgp 65002R1(config-router)#neighbor 192.168.50.2 shutdown  R1(config)#no ip route 192.168.50.2 255.255.255.255 Gi0/0  R1(config)#ip route 2.2.2.2 255.255.255.255 192.168.50.2 NEW QUESTION 190Refer to the exhibit.What step resolves the authentication issue?  use basic authentication  change the port to 12446  target 192 168 100 82 in the URI  restart the vsmart host he first figure is the output of the “show control connections” command. From this figure we learned that the 192.168.100.82 so we need to connect to this IP address (not 192.168.100.80).NEW QUESTION 191An engineer creates the configuration below. Drag and drop the authentication methods from the left into the order of priority on the right. Not all options are used. NEW QUESTION 192Drag and drop the virtual component from the left onto their descriptions on the right. Explanation+ configuration file containing settings for a virtual machine such as guest OS: VMX+ component of a virtual machine responsible for sending packets to the hypervisor: vNIC+ zip file containing a virtual machine configuration file and a virtual disk: OVA+ file containing a virtual machine disk drive: VMDKThe VMX file simply holds the virtual machine configuration.VMDK (short for Virtual Machine Disk) is a file format that describes containers for virtual hard disk drives to be used in virtual machines like VMware Workstation or VirtualBox.An OVA file is an Open Virtualization Appliance that contains a compressed, “installable” version of a virtual machine. When you open an OVA file it extracts the VM and imports it into whatever virtualization software you have installed on your computer.NEW QUESTION 193Refer to the exhibit.After an engineer configures an EtherChannel between switch SW1 and switch SW2, this error message is logged on switch SW2.Based on the output from SW1 and the log message received on Switch SW2, what action should the engineer take to resolve this issue?  Configure the same protocol on the EtherChannel on switch SW1 and SW2.  Connect the configuration error on interface Gi0/1 on switch SW1.  Define the correct port members on the EtherChannel on switch SW1.  Correct the configuration error on interface Gi0/0 switch SW1. ExplanationIn this case, we are using your EtherChannel without a negotiation protocol. As a result, if the opposite switch is not also configured for EtherChannel operation on the respective ports, there is a danger of a switching loop.The EtherChannel Misconfiguration Guard tries to prevent that loop from occuring by disabling all the ports bundled in the EtherChannel.NEW QUESTION 194Refer to exhibit.VLANs 50 and 60 exist on the trunk links between all switches All access ports on SW3 are configured for VLAN 50 and SW1 is the VTP server Which command ensures that SW3 receives frames only from VLAN50?  SW1 (config)#vtp pruning  SW3(config)#vtp mode transparent  SW2(config)=vtp pruning  SW1 (config >>vtp mode transparent NEW QUESTION 195Drag and drop the descriptions of the VSS technology from the left to the right. Not all options are used. ExplanationGraphical user interface Description automatically generatedNEW QUESTION 196Refer to the exhibit.Link1 is a copper connection and Link2 is a fiber connection. The fiber port must be the primary port for all forwarding. The output of the show spanning-tree command on SW2 shows that the fiber port is blocked by spanning tree. An engineer enters the spanning- tree port-priority 32 command on GO/1 on SW2, but the port remains blocked. Which command should be entered on the ports that are connected to Link2 to resolve the issue?  Enter spanning-tree port-priority 32 on SW1.  Enter spanning-tree port-priority 224 on SW1.  Enter spanning-tree port-priority 4 on SW2.  Enter spanning-tree port-priority 64 on SW2. ExplanationSW1 needs to block one of its ports to SW2 to avoid a bridging loop between the two switches.Unfortunately, it blocked the fiber port Link2. But how does SW2 select its blocked port? Well, the answer is based on the BPDUs it receives from SW1. answer ‘Enter spanning-tree port-priority 32 on SW1’ BPDU is superior than another if it has:1. answer ‘Enter spanning-tree port-priority 32 on SW1’ lower Root Bridge ID2. answer ‘Enter spanning-tree port-priority 32 on SW1’ lower path cost to the Root3. answer ‘Enter spanning-tree port-priority 32 on SW1’ lower Sending Bridge ID4. answer ‘Enter spanning-tree port-priority 32 on SW1’ lower Sending Port ID These four parameters are examined in order. In this specific case, all the BPDUs sent by SW1 have the same Root Bridge ID, the same path cost to the Root and the same Sending Bridge ID.The only parameter left to select the best one is the Sending Port ID (Port ID = port priority + port index). And the port index of Gi0/0 is lower than the port index of Gi0/1 so Link 1 has been chosen as the primary link.Therefore we must change the port priority to change the primary link. The lower numerical value of port priority, the higher priority that port has. In other words, we must change the port-priority on Gi0/1 of SW1 (not on Gi0/1 of SW2) to a lower value than that of Gi0/0.NEW QUESTION 197What is a characteristic of a next-generation firewall?  only required at the network perimeter  required in each layer of the network  filters traffic using Layer 3 and Layer 4 information only  provides intrusion prevention NEW QUESTION 198Refer to the exhibit.An engineer must permit traffic from these networks and block all other traffic An informational log message should be triggered when traffic enters from these prefixes Which access list must be used?  access-list acl_subnets permit ip 10.0.32.0 0 0.0.255 log  access-list acl_subnets permit ip 10.0.32.0 0.0.7.255 log  access-list acl_subnets permit ip 10.0.32.0 0.0.7.255 access-list acl_subnets deny ip any log  access-list acl_subnets permit ip 10.0.32.0 255.255.248.0 log NEW QUESTION 199A network administrator is implementing a routing configuration change and enables routing debugs to track routing behavior during the change. The logging output on the terminal is interrupting the command typing process.Which two actions can the network administrator take to minimize the possibility of typing commands incorrectly? (Choose two.)  Configure the logging synchronous global configuration command.  Configure the logging synchronous command under the vty.  Increase the number of lines on the screen using the terminal length command.  Configure the logging delimiter feature.  Press the TAB key to reprint the command in a new line. NEW QUESTION 200Refer to exhibit.VLANs 50 and 60 exist on the trunk links between all switches All access ports on SW3 are configured for VLAN 50 and SW1 is the VTP server Which command ensures that SW3 receives frames only from VLAN 50?  SW1(config)#vtp pruning  SW3(config)#vtp mode transparent  SW2(config)#vtp pruning  SW1(config)#vtp mode transparent SW3 does not have VLAN 60 so it should not receive traffic for this VLAN (sent from SW2).Therefore we should configure VTP Pruning on SW3 so that SW2 does not forward VLAN 60 traffic to SW3.Also notice that we need to configure pruning on SW1 (the VTP Server), not SW2.NEW QUESTION 201Refer to the exhibit.After an engineer configures an EtherChannel between switch SW1 and switch SW2, this error message is logged on switch SW2.Based on the output from SW1 and the log message received on Switch SW2, what action should the engineer take to resolve this issue?  Configure the same protocol on the EtherChannel on switch SW1 and SW2.  Connect the configuration error on interface Gi0/1 on switch SW1.  Define the correct port members on the EtherChannel on switch SW1.  Correct the configuration error on interface Gi0/0 switch SW1. NEW QUESTION 202Drag and drop the Qos mechanisms from the left to the correct descriptions on the right ExplanationA picture containing diagram Description automatically generated Loading … Master 2023 Latest The Questions CCNP Enterprise and Pass 350-401 Real Exam!: https://www.braindumpsit.com/350-401_real-exam.html --------------------------------------------------- Images: https://blog.braindumpsit.com/wp-content/plugins/watu/loading.gif https://blog.braindumpsit.com/wp-content/plugins/watu/loading.gif --------------------------------------------------- --------------------------------------------------- Post date: 2023-02-06 10:49:12 Post date GMT: 2023-02-06 10:49:12 Post modified date: 2023-02-06 10:49:12 Post modified date GMT: 2023-02-06 10:49:12