NACE NACE-CIP1-001 Daily Practice Exam New 2023 Updated 100 Questions [Q30-Q47] : IT Certification Exam Braindumps : http://blog.braindumpsit.com

NO.30 Digital hygrometers

consist of a bimetallic sensing element protected from wind gusts.

are used to measure temperature from a distance.

use a thermocouple in contact with the surface to measure temperature

determine relative humidity, air temperature, and dew point temperature:

NO.31 Prior to using Inspection Tools the inspector must:

Ensure the instrument is within calibration parameters

Be trained on how to use the instrument

Read the manufactures’ instructions

a), b) & c)

NO.32 You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?

105 Gauge Readings resulting in 35 Spot Measurements

75 Gauge Readings resulting in 25 Spot Measurements

225 Gauge Readings resulting in 75 Spot Measurements

45 Gauge readings resulting in 15 Spot Measurements

NO.33 Corrosion generally occurs at which of the following sites:

Cathode

Metallic pathway

Electrolyte

Anode

NO.34 Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners’ representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:

Gather data and attempt to meet with the owner’s representative in advance of the pre-job conference

Bring the matter up at the pre-job conference

Default to the owner’s Inspection and Test Plan

Meet separately with the coating manufactures’ representative and coating application company in advance of the pre-job conference

NO.35 Owners hire NACE Inspectors’ with the expectation that:

The inspection cost will be offset by an improvement in service life

The Inspector will improve job flow and schedule

The Inspector will make a meaningful technical contribution to the job

a) and c)

NO.36 To be of value the Inspector’s documentation must be:

Always handwritten

Always typewritten

Timely, accurate and concise

Submitted before the end of the job

NO.37 A magnetic pull-off type gauge is a good choice when:

Accuracy is not required

When an intrinsically safe tool is required

Performing an adhesion test

When working on non-ferrous metals

NO.38 What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?

70% of the specified maximum thickness

80% of the specified minimum thickness

90% of the specified maximum thickness

100% of the specified maximum thickness

NO.39 It is good practice for the NACE Inspector to have instrument calibration certificates available:

At all times

In the office only

In the field only

Only if the specification requires it

NO.40 Inspection documentation is important because:

It is the only deliverable item provided by the inspector

Owners use the documentation for a variety of purposes

a) only

a) & b)

NO.41 If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use

a recognized industry standard like SSPC-PA 2 that is broadly accepted

NACE 2/SSPC SP10

their best judgment based on similar projects and specifications.

a detailed checklist and document the lack of a standard.

NO.42 Inspector’s daily reports are used:
Select All That Apply

By the contractor to estimate the amount of work done that day

To provide continuity between inspectors

To aid in arbitration between the contractor and client

To help in cases of a coating failure

NO.43 A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?

5 to 6 mils (125 to 150 microns)

10 to 12 mils (250 to 300 microns)

8 to 10 mils (200 to 250 microns)

6 to 7 mils (150 to 175 microns)

NO.44 When applying Thermal Spray Coatings the specification is most likely to refence:

SSPC PA 2

NACE SP 0178

NACE SP 0188

SSPC-CS 23.00/AWS C2.23/NACE No. 12

NO.45 Excess moisture during holiday testing can cause erroneous indications by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection.
This is often referred to as:

telegraphing.

monitoring

juxtaposing.

transitioning.

NO.46 ISO SA 2.5 is defined as:

Near White Metal Blasting

Thorough Blast Cleaning

Very Thorough Blast Cleaning

Light Blast Cleaning

NO.47 You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:

Break the blisters to see what’s inside

Document the problem and advise the Contractor and Owner’s representative

Document the problem and advise the Contractor

Extract any liquid that may be inside the blister and send it to the lab for further analysis