[May 02, 2023] Pass CCNP Service Provider 350-501 Exam With 373 Questions [Q134-Q151] : IT Certification Exam Braindumps : http://blog.braindumpsit.com

NO.134

Refer to the exhibit. Based on the show command output, which result is true after BGP session is established?

The IOS XR router advertises and accepts all routes to and from eBGP neighbor 192.168.2.2.

The IOS XR router advertises all routes to the neighbor 192.168.2.2, but it does not accept any routes from
192.168.2.2.

No routes are accepted from the neighbor 192.168.2.2, nor are any routes advertised to it.

The IOS XR router does not advertises any routes to the neighbor 192.168.2.2, but it accepts any routes from 192.168.2.2.

NO.135 Refer to the exhibit.

An engineer is configuring path selection on router R1 for two ASNs as shown. Which additional task must the engineer perform on Router 1 so that all outbound traffic utilizes the link between R1 and R3 to reach ASN
4567?

Configure a low weight on the peer to ASN 4567.

Configure a high weigh! on ihe peer to ASN 4567.

Configure an AS path prepend on the peer to ASN 4567.

Configure a high med on the peer to ASN 4567.

NO.136 Drag and Drop Question
Drag and drop the NAT64 descriptions from the left onto the correct NAT64 types on the right.

NO.137 Refer to the exhibit.

A network operator has two IPv4 and IPv6 dual-stacked network on each side of the IPv4 core network. The operator must be able to provide connectivity between them while using specific assigned IPv6 space provided from the company IP administrator team. Which technology should the network operator use to accomplish this goal?

6rd

NAT46

DS-Lite

NAT44

NO.138 Drag and drop the OSs from the left onto the correct deceptions on the right.

NO.139 Drag and drop the LDP features from the left onto their usages on the right.

NO.140 Which configuration modifies Local Packet Transport Services hardware policies?
A)

B)

C)

D)

Option A

Option B

Option C

Option D

NO.141 A regional MPLS VPN provider operates in two regions and wants to provide MPLS L3VPN service for a customer with two sites in these separate locations. The VPN provider approaches another organization to provide backbone carrier services so that the provider will connect to these two locations.
What is the next step?

When edge at different regional sites are connected over the global carrier backbone, MP-eBGP must run between routers to exchange the customer VPNv4 routes.

When BGP is used for both route and label exchange, the neighbor a.b.c.d send-label command is used under the address-family VPNv4 command mode.

When IGP used for route exchange and LDP for label exchange, MPLS is enabled only on the VRF interface on the backbone-carrier PE side.

When eBGP is used for label exchange using the send-label option. MPLS-BGP forwarding is configured under the global ABC CSC PE-to-CE interface.

NO.142 Which QoS model allows hosts to report their QoS needs to the network?

IntServ

CB-WFQ

DiffServ

MQC

NO.143 Drag and drop the functionalities from the left onto the correct target fields on the right.

NO.144 Refer to the exhibit:

Assume all other configurations are correct and the network is otherwise operating normally. Which conclusion can you draw about the neighbor relationship between routers R1 and R2?

The neighbor relationship will be up only if the two devices have activated the correct neighbor relationships under the IPv4 address family

The neighbor relationship is down because R1 believes R2 is in AS 65012.

The neighbor relationship is up

The neighbor relationship is down because the loco I-as value for R2 is missing in the R1 neighbor statement

NO.145 A network engineer must enable the helper router to terminate the OSPF graceful restart process if it detects any changes in the LSA. Which command enables this feature?

nsf ietf helper disable

nsf cisco enforce global

nsf ietf helper strict-lsa-checking

nsf Cisco helper disable

NO.146 Refer to the exhibit:

With which router does IOSXRV-1 have LDP session protection capability enabled but session hold up is not active?

192.168.0.1

192.168.0.3

192.168.0.4

192.168.0.5

NO.147 Drag and drop the NAT64 descriptions from the left onto the correct NAT64 types on the right.

NO.148 Refer to the exhibit. What reestablishes the OSPF neighbor relationship between Router 1 and Router 2?

authentication is added to the configuration

correct wildcard mask is used on Router 2

OSPF process IDs match

hello intervals match

NO.149 Refer To the exhibit.

Which BGP attribute should be manipulated to have CE1 use PE1 as the primary path to the Internet?

The weight attribute should be manipulated on PE1 on outbound routes advertised to CE1.

The MED should be manipulated on CE1 on inbound routes from PE1.

The local preference attribute should be manipulated on PE2 on inbound routes advertised to CE1.

The origin of all routes should be modified on each router on inbound and outbound routes advertised to CE1.

NO.150 Refer to the exhibit. The link between Office A and Office B is running at 90% load, and occasionally the CPU on router R1 is overloaded. The company implemented QoS for business- critical applications at both offices as a temporary solution. A network engineer must update the R1 configuration to 600 ms to reduce CPU load and limit downtime after connection failure to avoid data loss. Which action meets this requirement?

Configure the fast-hello feature for OSPF with the command ip ospf dead-interval minimal hello- multiplier 3.

Configure BFD demand mode with the command bfd-demand timer 150 interval 250 retransmit 5.

Configure BFD non-echo mode with the command echo interval 250 minimal 300 echo-multiplier 2.

Configure BFD echo mode with the command bfd interval 150 min_rx 200 multiplier 3.