This page was exported from IT Certification Exam Braindumps [ http://blog.braindumpsit.com ] Export date:Wed Apr 16 16:32:07 2025 / +0000 GMT ___________________________________________________ Title: Latest JN0-451 Exam Dumps Juniper Exam from Training Expert BraindumpsIT [Q37-Q55] --------------------------------------------------- Latest JN0-451 Exam Dumps Juniper Exam from Training Expert BraindumpsIT Pass Juniper Mist AI - Specialist (JNCIS-MistAI) PDF Dumps | Recently Updated 82 Questions Juniper JN0-451 (Mist AI - Specialist (JNCIS-MistAI)) Certification Exam is designed for IT professionals who want to specialize in Mist AI, a leading-edge technology that enables the automation and optimization of network operations. Mist AI - Specialist (JNCIS-MistAI) certification exam is part of the Juniper Networks Certification Program, which offers a comprehensive and industry-recognized set of certifications for networking professionals.   NO.37 A user with a PSK calls you and says, “The Wi-Fi worked for a week and now it does not work.” There have not been any recent configuration changes to the network. You suspect that a time-based setting has reset the key.In this scenario, where would you begin troubleshooting?  Site-level Pre-Shared Keys  Organization-level Pre-Shared Keys  WLAN-level Pre-Shared Keys  RADIUS Pre-Shared Keys ExplanationIn this scenario, you would begin troubleshooting by checking the WLAN-level Pre-Shared Keys.NO.38 Referring to the exhibit, you asked Marvis to troubleshoot a client. In this scenario, what did Marvis determine?  two authentication failures over this week  two DHCP failures today  DHCP errors over the past seven days  two authentication failures today Reference:According to the exhibit, Marvis determined that there were two authentication failures today for the client device. This can be seen from the red dots on the timeline chart that indicate failed events and from the event details that show authentication failure as the reason.NO.39 Click the Exhibit button.Referring to the exhibit, in the USA, which two statements are correct? (Choose two.)  The WLAN with SSID Eero1234 is not configured to industry best practices.  The WLAN with SSID Eero1234 is configured to industry best practices.  The WLAN with SSID NETGEAR24 is not configured to industry best practices.  The WLAN with SSID NETGEAR24 is configured to industry best practices. Referring to the exhibit and considering that it is in the USA, the WLAN with SSID Eero1234 is not configured to industry best practices while the WLAN with SSID NETGEAR24 is configured to industry best practices.NO.40 You are using location-based services (LBS) at a new warehouse and placed the APs on the floor plan with the correct scale. The APs are mounted on trusses, 14 feet (4.3 meters) from the floor.Which two actions ensure correct location accuracy in this scenario? (Choose two.)  Install Virtual Beacons in each aisle.  Configure the height of each AP.  Determine the orientation of each AP.  Disable the 2.4 GHz Wi-Fi radios to reduce interference. ExplanationWhen using location-based services (LBS) at a new warehouse and placing APs on the floor plan with correct scale while ensuring correct location accuracy in this scenario where APs are mounted on trusses 14 feet (4.3 meters) from floor, two actions that should be taken are installing Virtual Beacons in each aisle and configuring height of each AP. So the correct answers are A. Install Virtual Beacons in each aisle and B.Configure height of each AP.NO.41 Click the Exhibit button.Referring to the exhibit, what is the meaning of the AI VALIDATED status update?  The issue was opened and is unresolved.  The issue was opened and Marvis confirms it has been closed.  The issue was opened and Marvis has closed it.  The issue was opened and closed manually. ExplanationThe AI VALIDATED status update means that the issue was opened and Marvis confirms it has been closed.NO.42 Click the Exhibit button.Referring to the exhibit, in the USA, which two statements are correct? (Choose two.)  The WLAN with SSID Eero1234 is not configured to industry best practices.  The WLAN with SSID Eero1234 is configured to industry best practices.  The WLAN with SSID NETGEAR24 is not configured to industry best practices.  The WLAN with SSID NETGEAR24 is configured to industry best practices. ExplanationReferring to the exhibit and considering that it is in the USA, the WLAN with SSID Eero1234 is not configured to industry best practices while the WLAN with SSID NETGEAR24 is configured to industry best practices.NO.43 Which two SLEs measure the amount of time that it takes for a process to complete? (Choose two.)  roaming  AP uptime  throughput  time to connect NO.44 Click the Exhibit button.Referring to the exhibit, which statement is correct about the Post-Install user’s role?  It is used for help desk monitoring and workflow for all sites.  It has access limited to installing APs and switches at all sites.  It has read-only access to all sites.  It has full access to all sites. NO.45 Click the Exhibit button.Referring to the exhibit, as part of the Throughput SLE in the Mist UI, the Coverage classifier indicates the signal strength of which device?  the AP’s radio strength  the signal strength between APs  the client  the AP’s radio for a single SSID NO.46 Which two Mist Aps would be used for BLE location? (Choose two.)  AP12  AP33  AP32  AP43 According to the JNCIS-MistAI Certification page2, two Mist APs that would be used for BLE location are AP33 and AP43. These are the only two models that support vBLE array technology, which enables accurate location services without physical beacons.NO.47 Referring to the exhibit, what are two reasons why a Mist AP would have multiple IP addresses? (Choose two.)  One IP address is used for control traffic and one address is used for management traffic.  The Local Status Page is enabled in the site settings.  One IP address is used for redundancy.  A guest portal is configured on a tagged VLAN. NO.48 You receive a Marvis Actions alert informing you that there is a non-compliant AP at one of your sites.What should you do to correct the problem?  Request an RMA.  Disconnect the Rogue AP from your Ethernet switch.  Replace the AP with the correct hardware model.  Install the correct version of firmware on the AP. According to the Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide2, a non-compliant AP is an AP that has a different hardware model than what is expected by the cloud configuration. This can happen when an AP is replaced with an incorrect model or when an AP is moved to a different site group that has a different hardware model requirement. The solution is to replace the AP with the correct hardware model.NO.49 What is meant when a Marvis Action is shown as “AI Validated”?  The issue which triggered an alert has been set to Resolved status.  Marvis has observed a new issue.  Marvis has observed a recurring issue.  Marvis has observed an issue that is no longer present. Reference:When a Marvis Action is shown as “AI Validated”, it means that Marvis has observed an issue that is no longer present.NO.50 Click the Exhibit button.Referring to the exhibit, which statement is correct about the Post-Install user’s role?  It is used for help desk monitoring and workflow for all sites.  It has access limited to installing APs and switches at all sites.  It has read-only access to all sites.  It has full access to all sites. Explanationthe Post-Install user role is also known as Installer role, which has a minimum level of access to the org, sites, and APs. It can do the initial installation such as claim AP to Org, assign/unassign AP, or place on map, etc., but cannot unclaim or remove the AP from the Org. Site and AP access is allowed based on timed grace period and/or explicit site access.https://www.mist.com/documentation/mist-ai-mobile-app/NO.51 Asset tracking using Mist-supported third-party BLE beacons has been installed in a warehouse. The BLE beacons were configured using their manufacturer-supplied configuration utility and BLE was properly configured for the site settings. When the warehouse floor plan is opened in Live View, the third-party beacons are not shown.Which two statements describe causes for this issue? (Choose two.)  The Show assets check box has not been selected in Live View.  Marvis was not enabled for the site.  The Locate this Client as an Asset check box has not been selected at the BLE client level.  The APs are installed at 19 feet from the floor, above the recommended 15 feet. NO.52 What do 802.11 stations perform to help avoid collisions on the WLAN medium?  802.11 stations detect collisions and set a back-off timer.  Listen to verify that the medium is free before transmitting.  Stations only transmit when polled by the access point.  Transmit on a fixed schedule. Reference:According to the IEEE 802.11 – Wikipedia document, one thing that 802.11 stations perform to help avoid collisions on the WLAN medium is to listen to verify that the medium is free before transmitting. This is part of the carrier-sense multiple access with collision avoidance (CSMA/CA) mechanism that 802.11 stations use to coordinate access to the shared medium.NO.53 You are deploying multiple Mist APs across many sites in your network. You must ensure that you apply consistent WxLAN and WLAN policies across all sites within the same organization.Which configuration object should be used to accomplish this behavior?  site labels  an RF template  a device profile  a config template NO.54 Which two statements are correct about the radio frequency rule of 10s and 3s? (Choose two.)  If the signal strength increases by 3 dB, the power is doubled.  If the signal strength decreases by 10 dB, the power decreases tenfold.  If the signal strength increases by 3 dB, the power is tripled.  If the signal strength decreases by 10 dB, the power is halved. NO.55 You are installing and booting up your first Juniper Mist AP at your site.By default, which two statements are correct in this scenario? (Choose two.)  The AP will attempt to connect to the Mist cloud using port 443.  The AP will send DHCP requests using the native VLAN.  The AP will send DHCP requests with a VLAN ID of 10.  The AP will attempt to connect to the Mist cloud using port 8080. According to the Initial AP Connection and VLANs & Static IP addresses – Mist document1, when a Juniper Mist AP boots up for the first time, it will expect to see a trunked port or the native VLAN=1 and will send a DHCP request on that VLAN. The AP will attempt to connect to the Mist cloud using port 443, which is the default HTTPS port. Loading … Juniper JN0-451 (Mist AI - Specialist (JNCIS-MistAI)) exam is a certification test designed for IT professionals who specialize in the Juniper Mist AI platform. JN0-451 exam validates the skills and knowledge of the candidates related to configuring, managing, and troubleshooting the Mist AI platform. JN0-451 exam is essential for IT professionals who want to demonstrate their expertise in implementing the Juniper Mist AI platform and help their organizations leverage the intelligence and automation capabilities of the platform.   Updated Test Engine to Practice JN0-451 Dumps & Practice Exam: https://www.braindumpsit.com/JN0-451_real-exam.html --------------------------------------------------- Images: https://blog.braindumpsit.com/wp-content/plugins/watu/loading.gif https://blog.braindumpsit.com/wp-content/plugins/watu/loading.gif --------------------------------------------------- --------------------------------------------------- Post date: 2023-07-17 12:19:25 Post date GMT: 2023-07-17 12:19:25 Post modified date: 2023-07-17 12:19:25 Post modified date GMT: 2023-07-17 12:19:25