[Q24-Q45] HPE6-A75 PDF Download Dec-2023 HP Test To Gain Brilliante Result!

Rate this post

HPE6-A75 PDF Download Dec-2023 HP Test To Gain Brilliante Result!

Provide Updated HP HPE6-A75 Dumps as Practice Test and PDF

NEW QUESTION 24
Refer to the exhibit.

An AD user’s department attribute is configured as *HR”. The user connects on Monday using their Windows Laptop to a switch that belongs to the Device Group HQ.
Which role is assigned to the user in ClearPass?

Executive

iOS Device

Vendor

Remote Employee

HR Local

NEW QUESTION 25
An AOS-Switch enforces 802.1X authentication to an Aruba ClearPass server. A user connects but cannot receive network access, even though the ClearPass administrator finds an Access- Accept for the user on this switch. The switch administrator suspects that there is an issue with the dynamic settings returned by ClearPass.
Where should the administrator look for information about these settings?

in the details for port-access clients

in the detailed RADIUS server statistics

in the interface statistics

in the running-config for the interface

NEW QUESTION 26
What are Operator Profiles used for?

to enforce role based access control for Aruba Controllers

to enforce role based access control for ClearPass Policy Manager admin users

to enforce role based access control for ClearPass Guest Admin users

to assign ClearPass roles to guest users

to map AD attributes to admin privilege levels in ClearPass Guest

NEW QUESTION 27
Refer to the exhibit.

The network administrator wants to reduce failover time If a switch link m VIAN 100 goes down. What should the administrator do?

Configure echo mode BFD on VLAN 100 on all OSPF routing devices on VLAN 100.

Lower the dead timer on the BDR of VLAN 100.

Lower the hello timer only on the BDR of VLAN 100.

Configure graceful restart on all of the OSPF routing devices on VLAN 100.

NEW QUESTION 28
Refer to the exhibit.

A known unicast packet is received from Switch-1 on the standby and must be forwarded to Switch-2. How does the VSF fabric decide which port in the aggregated (ink should forward the packet?

The standby uses its own port in the link aggregation to forward the fabric.

The standby sends the packet to the commander over a VSF link, and the commander decides the correct port.

The standby uses the typical load sharing algorithm, and it might select either its port or the commander’s port.

The standby selects the port on the designated forwarder for the aggregation.

NEW QUESTION 29
What is a typical reason to implement MAC authentication on an AOS-Switch?

to filter traffic at the edge, based on multiple criteria in the MAC header

to provision switch ports to support devices such as IP phones or printers

to enhance the security of an 802.1X solution

to control management access to the switch CLI based on device, as well as user credentials

NEW QUESTION 30
The administrator expects the AP to connect to a cluster, but the AP tails to connect. The administrator examines the configuration of an AP from apboot mode shown in the exhibit. What can the administrator determine about the configuration of the AP?

The AP is configured to terminate on a non-cluster Mobility Controller.

The AP is configured as a RAP to terminate on a stand-alone controller.

The AP is configured as a RAP to terminate on a Mobility Master.

The AP is configured to terminate on a Mobility Controller in a cluster.

NEW QUESTION 31
Refer to the exhibit.

An Enforcement Profile has been created in the Policy Manager as shown. Which action will ClearPass take based on this Enforcement Profile?

ClearPass will count down 600 seconds and send a RADIUS CoA message to the user to end the user’s session after this time is up.

ClearPass will send the Session-Timeout attribute in the RADIUS Access-Accept packet to the NAD and the NAD will end the user’s session after 600 seconds.

ClearPass will count down 600 seconds and send a RADIUS CoA message to the NAD to end the user’s session after this time is up.

ClearPass will send the Session-Timeout attribute in the RADIUS Access-Request packet to the NAD and the NAD will end the user’s session after 600 seconds.

ClearPass will send the Session-Timeout attribute in the RADIUS Access-Accept packet to the User and the user’s session will be terminated after 600 seconds.

NEW QUESTION 32
Which solution allows administrators to monitor link status and port utilization on AOS-Switches from a centralized location?

Aruba Mobility Controller

Aruba AirWave

Aruba Mobility Manager

Aruba ClearPass

NEW QUESTION 33
The security plan for AOS-Switches calls for ARP protection. For ARP protection to function properly, which other feature should also be implemented?

MAC lockout

proxy ARP

DHCP snooping

connection-rate filtering

NEW QUESTION 34
Refer to the exhibit.

Based on the configuration of me create_user form shown, which statement accurately describes the status?

The email field will be visible to guest users when they access the web login page.

The visitor_company field will be visible to operators creating the account.

The visitor_company field will be visible to the guest users when they access the web login page.

The visitor_phone field will be visible to the guest users in the web login page.

The visitor_phone field will be visible to operators creating the account.

NEW QUESTION 35
A network administrator can set the OSPF metric-type on an AOS-Switch to Type 1 or Type 2. What is the difference?

A Type 2 metric marks external routes that can be advertised in NSSAs, while a Type 1 metric marks external routes that can only be advertised in normal areas.

A Type 2 metric assigns cost 1 to a 100 Gbps link, while a Type 1 metric assigns cost 1 to all links of 100 Mbps or higher.

A Type 2 metric is assigned to multiple external routes that are aggregated together, while a Type 1 metric does not permit external route aggregation.

A Type 2 metric stays the same as the external route is advertised, while a Type 1 metric increments with internal OSPF link costs.

NEW QUESTION 36
An administrator wants to use Airwave to manually add devices on the network. Where should the administrator perform this action?

in Device Setup

in Groups

in AMP Setup

in Devices

NEW QUESTION 37
A company has AOS-Switches deployed at sites with inexperienced IT staff. The main office network administrators want to track if configurations change on branch switches. What should be set up for this purpose?

an SNMP trap

an RMON alarm

an auto-config server

an lP SLA profile

NEW QUESTION 38
Refer to the exhibit.

A network administrator sets up 802.1X authentication to a RADIUS server on an AOS-Switch. The RADIUS server and user devices are both set up to use REAP MSCHAPv2. The administrator tests the authentication and sees the output shown in the exhibit. Which issue could cause this output?

The RADIUS shared secret does not match on the switch and the server.

The administrator entered the wrong password for the test account.

The switch does not have a certificate tor port-access installed on the switch.

The switch port is set for user mode 801. IX. but the RADIUS server is set for port mode.

NEW QUESTION 39
Refer to the exhibit.

Based on the Enforcement Policy configuration, when a user with Role Engineer connects to the network and the posture token assigned is Unknown, which Enforcement Profile will be applied?

EMPLOYEE_VLAN

RestrictedACL

Deny Access Profile

HR VLAN

Remote Employee ACL

NEW QUESTION 40
Refer to the exhibit.

Which statements accurately describe the status of the Onboarded devices in the configuration tor the network settings shown? (Select two.)

They will connect to Employee_Secure SSID after provisioning.

They will connect to Employee_Secure SSID for provisioning their devices.

They will use WPA2-PSK with AES when connecting to the SSID.

They will connect to secure_emp SSID after provisioning.

They will perform 802.1X authentication when connecting to the SSID.

NEW QUESTION 41
Refer to the exhibit.

Based on the configuration of the Enforcement Profiles In the Onboard Authorization service shown, which Onboarding action will occur?

The device will be disconnected from the network after Onboarding so that an EAP-TLS authentication is not performed.

The device will be disconnected from and reconnected to the network after Onboarding is completed.

The device’s onboard authorization request will be denied.

The device will be disconnected after post-Onboarding EAP-TLS authentication, so a second EAP- TLS authentication is performed.

After logging in on the Onboard web login page, the device will be disconnected form and reconnected to the network before Onboard begins.

NEW QUESTION 42
An administrator deploys an AP at a branch office. The branch office has a private WAN circuit that provides connectivity to a corporate office controller. An Ethernet port on the AP is connected to a network storage device that contains sensitive information. The administrator is concerned about sending this traffic in clear-text across the private WAN circuit.
What can the administrator do to prevent this problem?

Redirect the wired port traffic to an AP-to-controller GRE tunnel.

Convert the campus AP into a RAP.

Enable AP encryption for wired ports.

Enable IPSec encryption on the AP’s wired ports.

NEW QUESTION 43
Refer to the exhibit.

Based on the configuration of the Enforcement Profiles In the Onboard Authorization service shown, which Onboarding action will occur?

The device will be disconnected from the network after Onboarding so that an EAP-TLS authentication is not performed.

The device will be disconnected from and reconnected to the network after Onboarding is completed.

The device’s onboard authorization request will be denied.

The device will be disconnected after post-Onboarding EAP-TLS authentication, so a second EAP-TLS authentication is performed.

After logging in on the Onboard web login page, the device will be disconnected form and reconnected to the network before Onboard begins.

NEW QUESTION 44
Refer to the exhibit.

The network administrator needs to set up BGP between the two company switches. Switch-1 and Switch-2. The BGP connection does not establish. Based on the exhibits, what does the administrator need to do to fix the issue?

Enable the multihop option for the neighbor on each of the switches.

Enter the network command for 10.0.0.0/24 in the router BGP mode on each switch.

Enable BGP on the interfaces that the switches use to reach each other.

Set the update source for the neighbor to the local loopback interface on each switch.

NEW QUESTION 45
Refer to the exhibit.

Based on the configuration for the client’s certificate private key as shown, which statements accurately describe the settings? (Select two.)