New Cisco 350-501 Dumps & Questions Updated on 2023 [Q153-Q168]

4/5 - (1 vote)

New Cisco 350-501 Dumps & Questions Updated on 2023

Dumps to Pass your 350-501 Exam with 100% Real Questions and Answers

Cisco 350-501 exam focuses on various areas, including network automation, network virtualization, network assurance, security, and services. 350-501 exam validates the candidate’s knowledge and skills in managing and configuring various technologies, such as MPLS, Segment Routing, and VPN services. Additionally, the exam also covers topics such as network programmability, network management, and network security, which are crucial for service provider network engineers. Passing 350-501 exam demonstrates that the candidate has the expertise and skills required to implement and operate service provider networks, making them highly valuable to companies that rely on such networks.

Q153. Refer to the exhibit:

With which router does IOSXRV-1 have LDP session protection capability enabled but session hold up is not active?

192.168.0.1

192.168.0.3

192.168.0.4

192.168.0.5

Q154. How much must the MTU be increased when configuring the 802.1q VLAN tag?

2 bytes

4 bytes

8 bytes

12 bytes

Section: Networking
Explanation/Reference: https://www.cisco.com/c/en/us/support/docs/lan-switching/8021q/17056-741-4.html

Q155. A network architect decides to expand the scope of the multicast deployment within the company network. The network is already using PIM-SM with a static RP that supports a high-bandwidth, video-based training application that is heavily used by the employees, but excessive bandwidth usage is a concern. How must the engineer update the network to provide a more efficient multicast implementation?

Configure IGMP to manage the multicast hosts on each LAN

Implement BSR to support dynamic RP notification.

Deploy ICMP to Improve multicast reachability across the network using static RP.

Implement STP to improve switching performance for multicast data.

Q156. Which two IS-IS parameters must match before two Level 2 peers can form an adjacency? (Choose two )

authentication settings

area ID

system ID

MTU

hello timer setting

Q157. What Is the primary role of Ansible In a network?

It is used as a debugging tool for connectivity issues between the DMZ and an enterprise intranet.

It Is used to diagnose Layer 11ssues In data centers that span more than one city block.

It is used to deploy IPv6 configuration is networks That are dual slack.

It is used as a network automation provisioning and configuration tool.

Q158. A customer of an ISP requests support to setup a BGP routing policy. Which BGP attribute should be configured to choose specific BGP speakers as preferred points for the customer AS?

lowest multi-exit discriminator

highest local preference outbound

lowest local preference inbound

highest local preference inbound

Section: Networking

Q159. Refer to the exhibit.

Which task completes the configuration?

Specify the maximum number of prefixes that R1 receives from neighbor 192.168.1.2.

Specify the source interface in the neighbor statement.

Specify the activate neighbor 192.168.1.2 under the IPv4 address family.

Specify the local-as value in the neighbor statement.

Q160. Refer to the exhibit.

While troubleshooting the network, a network operator with an employee id: 3812:12:993 is trying to ping XR1. Which result should the operator expect when trying to ping to an XR1 local address?

ICMP traffic works at a policed rate of 19 bytes per second every 100 ms

All ICMP traffic responds successfully.

All ICMP traffic is dropped.

ICMP traffic works at a policed rate of 19 packets every 100 ms.

Q161. Refer to the exhibit:

P3 and PE4 are at the edge of the service provider core and serve as ABR routers Aggregation areas are on either side of the core.
Which statement about the architecture is true?

If each area is running its own IGP. the ABR routers must redistribute the IGP routing table into BGP

To support seamless MPLS. TDP must be used as the label protocol

If each area is running its own IGP. BGP must provide an end-to-end MPLS LSP

To support seamless MPLS, the BGP route reflector feature must be disabled

Q162. Refer to the exhibit.

An engineer is configuring router R1 for OSPFv3 as shown. Which additional configuration must be performed so that the three active interfaces on the router will advertise routes and participate in OSPF IPv6 processes?

from 2.2.2.2, with a TTL of less than 2

to 2.2.2.2, with a TTL of less than 253

from 2.2.2.2, with a TTL of 253 or more

to 2.2.2.2, with a TTL of 2 or more

Q163. Which statement about Network Services Orchestrator (NSO) is true?

It must use SDN as an overlay for addressing.

It uses YANG modeling language to automate devices.

It is used only in service provider environments.

It can be used only with XML coding.

Section: Automation and Assurance

Q164. Which module refers to the network automation using Ansible?

the losxr_command module to issue run commands on remote devices

the losxr_system module to collect facts from remote devices

the losxr_logging module to run debugging for severity levels 2 to 5

the iosxr_user module to manage banners for users in the local database

Explanation
https://docs.ansible.com/ansible/latest/collections/cisco/iosxr/iosxr_command_module.html#ansible-collections-

Q165. You are writing an RPL scnpt to accept routes only from certain autonomous systems Consider this code.

If you apply this code to BGP filters, which effect does the code have on your router?

denies routes from AS 7070

allows routes from AS 7077

denies routes from AS 7007

allows routes from AS 770

Q166. Refer to the exhibit.

An engineer at a new ISP must configure many Cisco devices in the data center. To make the process more efficient, the engineer decides to automate the task with a REST API. Which action does this JSON script automate?