[2026] 300-515 by CCNP Service Provider Actual Free Exam Practice Test [Q68-Q88]

Rate this post

[2026] 300-515 by CCNP Service Provider Actual Free Exam Practice Test

Free CCNP Service Provider 300-515 Exam Question

Cisco 300-515 certification exam is targeted towards professionals who have experience working with VPN technologies and have a fundamental understanding of service provider networks. 300-515 exam is ideal for those who are looking to further their career in service provider network engineering, or for those who are looking to specialize in VPN technologies. 300-515 exam consists of 60-70 questions and is 90 minutes long, making it a challenging but achievable certification to obtain.

QUESTION 68
Refer to the exhibit.

Which effect of this configuration is true?

It configures VPWS multihomed.

It configures VPWS single homed.

It configures an IPv4 peering with 192.168.1.1

It configures MPLS traffic engineering.

QUESTION 69
Which two frames can be configured on an Ethernet flow point? (Choose two.)

of a specific VLAN

with different type of service values

with identical type of service value

with different class of service values

with no tags

QUESTION 70
Which mechanism reduces the network flooding caused by host ARP learning behavior?

ARP suppression

storm control

root guard

BPDU guard

QUESTION 71
Refer to the exhibit.

The CE router has established a BGP peering with the PE router, and the CE will use the core infrastructure of the PE as a backbone carrier to support CSC. Which additional task can you perform to complete the configuration?

Configure static routing on the CE router.

Configure the address-family ipv4 labeled-unicast command under the neighbor configuration of the CE router for the PE.

Change the rd value to 65001:65001 under the VRF section of the PE router.

Configure OSPF on the PE router.

QUESTION 72
What is a requirement to share VRF reachability information to all members of a VPN when using IPv6?

PE and CE routers must be running BGP as the PE-CE routing protocol

PE routers must have MPLS disabled and be running MP-BGP between all P and PE routers.

PE routers must be running MP-BGP and bgp default ipv4-unicast must be disabled

All PEs must have the same VRFs configured.

QUESTION 73
Refer to the exhibit. What is shown in this output?

local and outgoing abels are updated in hardware

BGP is used between neighbors that are exchanging MPLS labels

LDP neighbor statuses

the labels received and advertised on PE1

QUESTION 74
Refer to the exhibit. PE routers PE2 and PE3 are each connected to a CE at a branch office belonging to the same small company, which connects to the internet via the service provider’s L3VPN. The company now requires connectivity between the two branch offices. A service provider engineer has already made the appropriate changes to PE3.
Which action must the engineer take under the customer’s VRF on PE2 to allow the two customer sites to communicate?

Add the PE3 route-target export value as the route-target export value.

Add the PE3 route-target export value as the route-target import value.

Add the PE2 route-target export value as the route-target export value.

Add the PE2 route-target export value as the route-distinguisher value.

QUESTION 75
Refer to the exhibit. A technician is troubleshooting a connectivity issue and notices that there is no IS-IS adjacency between R1 and R2. What can the technician change to bring the IS-IS adjacency up?

Change R2’s net address to be in the same area as R1.

Change R1’s is-type to level-2-only

Change R1’s net address to be in the same area as R2.

Change R2’s configuration to no longer set the overload bit.

QUESTION 76
How do VPNv6 routes propagate between CEs?

The CE uses NAT64 to translate the IPv6 address into a unique IPv4 address, which is sent between sites.

A DHCP server assigns an IPv4 address and an IPv6 address to each host, and the CE sends traffic from those hosts between sites.

The PE assigns an RD to each VRF and prepends the value to shared IPV6 routes, which allows two or more sites to use a single IP address space.

The CE uses Unified MPLS to assign labels to IPV6 traffic only, and then it sends traffic to the PEs using those labels.

QUESTION 77
Refer to the exhibit. A customer with a single site requested additional monitoring for Ethernet connections to its service provider. Ethernet OAM has been implemented on the link between CE1 and PE2.
Which command must be implemented on PE2?

ethernet oam max-rate 8

ethernet uni id 2004-20

ethernet oam min-rate 8

ethernet oam remote-loopback supported

QUESTION 78
Refer to the exhibit. Which statement describes the result of this configuration?

R1 redistributes BGP routes into the OSPF process of VRF custabc as E1 routes.

R1 redistributes BGP routes into the OSPF process of VRF custabc as E2 routes.

R1 mutually redistributes routes between BGP 65001 and the OSPF process of VRF custabc.

R1 redistributes BGP routes into the OSPF process of VRF custabc as OIA routes.

QUESTION 79
How do Ethernet virtual circuits provide a way for service providers to maximize the use of VLAN tags?

They add an additional tag to VLANs that allows up to two switch ports to use the same globally configured VLAN ID.

They redefine the VLAN tag to include classification, forwarding, and QoS using MPLS labels and EXP bits

They separate the classification and forwarding concepts for VLAN tagging which allows multiple switch ports to use the same VLAN ID without it being configured globally.

They assign VLAN IDs to VTP domains so that the same VLAN ID are used more than once globally.

QUESTION 80
What are two components of a VPNv4 address? (Choose two.)

import route target

MPLS label

IP address

route distinguisher

export route target

QUESTION 81
Refer to the exhibit. A network engineer with an employee ID: 5100:21:535 must configure routers PEA and PEB so that traffic between CE1 and CE2 is multihomed and load-balanced.
The two 10GE links in Ethernet bundle 10 are sending traffic at different rates. Which action must the engineer take on PEX and PEY to complete the configuration?

Set the identifier type 11.12.11.12.11.12.11.12.11 on the PEX and PEY routers.

Change the source and destination AC values to 5 and 6 respectively.

Set the identifier type 33.34.33.34.33.34.33.34.33 on the PEX and PEY routers.

Set the neighbor evpn vpi value to 200 on the PEX and PEY routers.

QUESTION 82
How does a virtual machine move seamlessly within a network in an EVPN environment?

The IP-to-MAC binding for the default gateway is maintained across the network independent of the location of the virtual machine.

The virtual machine sends out a broadcast message after changing locations to seamlessly identify its new default gateway.

A central server automatically assigns a new IP address to the virtual machine via dial-out.

The administrator updates the MAC address of the virtual machine in the CAM table after the virtual machine is moved.

QUESTION 83
While configuring the VRF Selection feature, you get an error message after typing the below statement:
Router(config)#no vrf selection source 172.16.0.0 255.255.0.0 vrf VRF1
Which action caused this message?

the entry of an inconsistent IP address and mask for VRF Selection

an attempt to configure a VRF instance on an interface that already has VRF Selection configured

an attempt to remove a VRF Selection entry that does not exist

an attempt to configure a VRF Selection table that does not exist

QUESTION 84
An engineer noticed that PE3 is failing to accept IPv6 traffic information from PE1.
The engineer confirmed that both PE3 and PE1 routers are configured accurately with IPv6 protocol.
To eliminate IPv6 traffic loss issue, which action must the engineer take to solve the problem?

Disable 6PVE that provides local IPv6 reachability over MPLS.

Configure 6PE that provides global IPv6 reachability over IPv4 MPLS

Allow PE routers use the MP-iBGP extensions in the IPv6 network configuration to exchange IPv6 reachability information.

Configure 6PE forwarding between 6PE routers based on the IPv6 header

QUESTION 85
What do routers on the network use to avoid routing loops when OSPF is running as the PE-CE routing protocol on a service provider network?

the AS-Override feature

the DN bit with type 3, 5, or 7 LSA

the domain tag for type 2 LSA

sham links to create a super backbone over the service provider network

QUESTION 86
Which configuration must be performed when an engineer implements MP-BGP to exchange IPV6 routes?

BGP peering must be activated under the IPv6 address family.

The bgp default ipv4-unicast command must be implemented on each router participating in MP- BGP.

BGP must be deployed in a fully meshed architecture within the autonomous system.

The participating routers must be configured within the same autonomous system

QUESTION 87
What must match in the EVPN and L2VPN configuration mode when configuring EVPN native in a router?

interface

address family

bridge domain

EVI

QUESTION 88
Refer to the exhibit. Router 1 is a P router in the ISP MPLS core.
A connected P router cannot generate an MPLS label for the router 1 loopback0 interface.
Which action resolves this issue?

The loopback0 interface must be in OSPF area 0.

The network statement under the routing process must have a wildcard mask of 0 0.0 255.

The OSPF network type must be changed on loopback0 to point-to-point

A static route to null 0 must be added for the loopback interface and then static routes must be redistributed into OSPF

Achieving the Cisco 300-515 certification can open up a range of career opportunities for professionals working in service provider networks. Implementing Cisco Service Provider VPN Services certification demonstrates that the candidate has the skills and knowledge required to implement VPN solutions in a service provider environment, which is a valuable asset for employers. It can also lead to higher salaries and more advanced job roles within the field.

Cisco 300-515 Actual Questions and Braindumps: https://www.braindumpsit.com/300-515_real-exam.html