NO.104

Refer to the exhibit. An engineer proposed this solution for a company that requires a loop-free. Layer 2 network design. The network will run 802.1W, and all links will be 1 Gbps. If all interfaces are up as point- to- point adjacencies, what are the expected port end states based on the design?

NO.105 Which function does the Cisco SD-Access intermediate node perform?

NO.106 Which design consideration must be made when using IPv6 overlay tunnels?

NO.107 Refer to the exhibit. An engineer is designing an OSPF solution with these requirements:
– NMS server will manage R5 and R6.
– Upon failure of R1, all NMS traffic should be routed through R4.
– Upon failure of the link between R5 and R6, all traffic destined for
10.6.6.6 should be routed through R4.
Which solution must the engineer choose?

NO.108 A company with multiple service providers wants to speed up BGP convergence time in the event a failure occurs with their primary link. Which approach achieves this goal and does not impact router CPU utilization?

NO.109 Drag and drop the elements from the left onto the protocols where they are used on the right.

NO.110 Refer to the exhibit.

Refer to the exhibit. Where must an architect plan for route summarization for the topology?

NO.111

Refer to the exhibit. Area 10 is a regular OSPF area and networks 10.1.1.0/24 and 172.16.1.0/24 are internal.
Which design provides optimal routing between both networks when the link between routers C and E fails?

NO.112 Which two LISP components are required in the Cisco SD-Access fabric control plane node?
(Choose two.)

NO.113 Which routes does the overlay management protocol advertise in an SD-WAN overlay?

NO.114 Which command is needed to enable DHCP snooping if a switchport is connected to a DHCP server?

NO.115 A network engineer must segregate three interconnected campus networks using IS-IS routing.
A two-layer hierarchy must be used to support large routing domains and to avoid more specific routes from each campus network being advertised to other campus network routers automatically.
Which two actions does the engineer take to accomplish this segregation? (Choose two.)

NO.116 A company wants to enable several third-party video conferencing networks based on multicast services. The video conferencing platform can accommodate numerous and dispersed senders and receivers in third-party networks The interior routing protocol is OSPF and the exterior routing protocol is BGP Which multicast mode must be selected to achieve this goal?

NO.117 An engineer is designing an IPv4 addressing plan for an enterprise with 1000 branches. Each branch requires a prefix for data and a prefix for voice. Each prefix must accommodate up to 128 hosts, and prefixes must facilitate summarization at aggregation points in the network. The security team requires a simple method for identifying voce prefixes. Which allocation does the engineer recommend from the RFC1918 address space?

NO.118 A company wants to switch from static routing to a dynamic routing protocol to ease the administrative and operational overhead. The network topology is hub and spoke, and the branches use DMVPN back to the hub using two 100 Mbps internet connections. Both links must be used due to spikes in traffic, and routing must take traffic utilization of the links into account.
Also, the branch routers have limited memory and CPU resources.
Which routing protocol and design solution must the company choose?

NO.119 An engineer is designing a campus network with Cisco Catalyst 9500 switches in the aggregation layer. The design requires running nonblocking Layer 2 MEC from the aggregation layer to the access layer. The Catalyst switches are located on different campus floors for availability reasons, and each access switch will contain a single VLAN. Which technology must the engineer choose for the aggregation switches in the design?

NO.120 Which topology within a network underlay eliminates the need for first hop redundancy protocols while improving fault tolerance, increasing resiliency, and simplifying the network?

NO.121 Refer to the exhibit.

An architect is designing a network for a customer supporting a Wake-on-LAN application. Which solution must the architect choose?

NO.122

Refer to the exhibit A customer requires a Layer 2 network designed to support:
* 500 active logical ports
* trunking of 30 VLANs
* convergence of less than 1 second
Which Spanning Tree Protocol must be selected?

NO.123 A company uses cloud-based applications for voice and video calls, file sharing, content sharing, and messaging. During business hours, these applications randomly become slow and unresponsive. However, other applications work smoothly with the current applied QoS polices.
Which solution must the company choose to resolve the issue?

NO.124 Which queuing structure is used on SD-WAN Edge routers?