FlashArray-Implementation-Specialist Dumps (2026) Prepare Your Exam With 236 Questions [Q21-Q35]

5/5 - (1 vote)

FlashArray-Implementation-Specialist Dumps (2026) Prepare Your Exam With 236 Questions

New FlashArray-Implementation-Specialist Dumps – Real Pure Storage Exam Questions

Pure Storage FlashArray-Implementation-Specialist Exam Syllabus Topics:

Topic	Details
Topic 1	Installation: This section of the exam measures the skills of Enterprise Infrastructure Technicians and focuses on executing a successful installation of FlashArray systems. It tests the ability to perform physical setup, cabling, configuration of network settings, and the application of initial system configurations necessary for full deployment.
Topic 2	Pre-Installation Upgrade: This section of the exam measures the skills of Enterprise Infrastructure Technicians and covers all preparation activities before deploying or upgrading a Pure Storage FlashArray. It includes understanding environmental requirements, verifying prerequisites, checking compatibility, and validating system readiness through appropriate tools and documentation.
Topic 3	Upgrades: This section of the exam measures the skills of FlashArray Implementation Specialists and focuses on tasks involved in managing firmware and software upgrades. Candidates must demonstrate knowledge of upgrade planning, verification steps, and rollback procedures, ensuring that systems are updated with minimal disruption to service.
Topic 4	Post-Installation Upgrade: This section of the exam measures the skills of FlashArray Implementation Specialists and evaluates how professionals confirm system functionality after installation or an upgrade. It involves validating connectivity, running health checks, confirming configurations, and ensuring that the deployment meets operational expectations.

NO.21 Before starting the HWNDU, the Implementation Engineer discovers that DirectFlash Shelf SH9 is incorrectly cabled to CT0.
What should the Implementation Engineer do?

Proceed with the HWNDU and fix the cable after the upgrade.

Reschedule the HWNDU until a plan to fix the cabling is ready.

Fix the cabling during the CT0 replacement.

Disconnect the shelf immediately to prevent data corruption.

NO.22 During an intra-series upgrade from //XR3 to //XR4, which command should the Implementation Engineer run to verify host connectivity before removing the secondary controller?

purehost list –hostless

iobalance –sampletime 30

host_connectivity –hosts

NO.23 FlashArray//C and //E models use which flash storage architecture, identifiable by gray tabs on the DirectFlash Module carriers?

TLC Flash

QLC Flash

SLC Flash

MLC Flash

NO.24 Once the new Purity firmware has been installed using the pureinstall command, what step is required to commit the new version?

Reboot the controller

Reboot the array

Log out of the controller

Run pureinstall –commit

NO.25 The Customer’s Implementation Workbook specifies that the SMTP reply is “outlook.microsoft.com:587”.
What correction should be made for array initialization to be successful?

Provide username and password.

Prefix the URL with “https://”.

Remove the port number.

NO.26 Which power cable receptacle type does the FlashArray//X accessory kit contain?

C19 to C20

C14 to C15

C13 to C14

NO.27 Which command should the Implementation Engineer use to easily verify connectivity to Pure1 from a FlashArray?

purearray test pinghome

puresupport phonehome

purearray phonehome test

NO.28 Which Purity command can be used to validate I/O is balanced across initiators?

purehost list –balance

purehost iobalance –check

purehost monitor –balance

NO.29 The Pure Engagement Request (PER) specifies that iSCSI ports ETH2 and ETH3 should be set to 10 Gb/s.
After configuring the ports and connecting them to the SAN, the Implementation Engineer observes that ETH2
/3 are not negotiating and display 0 b/s. The SAN is operating at 40 Gb/s, with support for up to 100 Gb/s.
What should the Implementation Engineer do to resolve this issue and complete the install?

Force negotiate the array iSCSI ports to 40 Gb/s.

Replace the transceivers with the appropriate type.

Force negotiate the switch iSCSI ports to 40 Gb/s.

Restart the Purity operating system to reset the network stack.

NO.30 The Customer’s Implementation Workbook specifies that the SMTP reply is “outlook.microsoft.com:587”. What correction should be made for array initialization to be successful?

Provide username and password.

Prefix the URL with “https://”.

Remove the port number.

NO.31 How many chassis capacity drive slots come standard on a FlashArray//X Gen 2 chassis?

28 slots

20 slots

24 slots

40 slots

NO.32 After running puredb run giveback –safe command once CT0 has been upgraded, how long should the Implementation Engineer wait before continuing with the controller upgrade?

3 minutes

5 minutes

10 minutes

NO.33 What slot does a PCIe SAS card need to be installed in a FlashArray//XR2/3?

NO.34 Which PCIe slot supports 4-port FC cards on FlashArray//XL?

NO.35 After rebooting a controller, which command should an Implementation Engineer run to verify all the Purity services have started successfully?

pureadm status –all

pureadm list –status

pureadm list

purecluster status